Titanium Weight vs Aluminum Weight: How to Choose the Best
Comparing titanium weight vs aluminum weight starts with density. Ti-6Al-4V, the most common titanium alloy, is about 4.43 g/cm³, while 6061 aluminum is about 2.70 g/cm³. So a titanium part is roughly 64% heavier than an aluminum part of the same shape. However, titanium is much stronger, so a redesigned titanium part can still end up lighter.
That is why the question “which is lighter?” has two answers. For example, a 100 × 50 × 20 mm block weighs about 270 g in 6061 and about 443 g in Ti-6Al-4V. But a bracket sized by strength can use far less titanium than aluminum. In this guide, we compare titanium weight vs aluminum weight for CNC machined parts, show when each metal saves mass, and explain the cost and machining trade-offs. For machining options, see our CNC machining services.
Titanium weight vs aluminum weight: for the same volume, Ti-6Al-4V (about 4.43 g/cm³) weighs about 1.64 times as much as 6061 aluminum (about 2.70 g/cm³). Because annealed Ti-6Al-4V has roughly three times the yield strength of 6061-T6, a part sized by strength can be lighter in titanium. A part sized by stiffness is usually lighter in aluminum, because both metals have similar stiffness per unit weight.
In short: aluminum wins on weight for equal shapes and stiff parts; titanium wins only when strength sets the size.
Key points:
- Same shape: titanium is about 64% heavier than 6061 aluminum.
- Strength-limited parts: titanium can be thinner and lighter.
- Stiffness-limited parts: aluminum is usually lighter.
How Does Titanium Weight vs Aluminum Weight Compare by Density?
Titanium weight vs aluminum weight compares directly through density, because mass equals volume times density. The table shows typical values for common machining alloys.
| Material (typical) | Density (g/cm³) | Weight vs 6061 for the same shape |
|---|---|---|
| 6061 aluminum | about 2.70 | baseline |
| 7075 aluminum | about 2.81 | about +4% |
| Ti-6Al-4V (Grade 5) | about 4.43 | about +64% |
| Commercially pure titanium (Grade 2) | about 4.51 | about +67% |
| Carbon steel | about 7.85 | about +191% |
Titanium sits between aluminum and steel in this titanium weight vs aluminum weight comparison. It is about 44% lighter than steel for the same volume, which is why it replaces steel in many weight-critical parts. Against aluminum, however, the same geometry is always heavier in titanium. Alloy specifications, such as those published by ASTM International, define the chemistry and properties behind these typical values.
Key Takeaway: Do not swap aluminum for titanium in the same model to save weight. The same shape gets heavier, not lighter.
How Do You Calculate Titanium Weight vs Aluminum Weight for a Part?
You calculate titanium weight vs aluminum weight for a part by multiplying the part volume by each material’s density. Most CAD systems report volume directly, so the calculation takes seconds.

Weight (g) = volume (cm³) × density (g/cm³)
A worked example for a solid block of 100 × 50 × 20 mm:
- Volume = 10 × 5 × 2 cm = 100 cm³
- 6061 aluminum: 100 × 2.70 = about 270 g
- Ti-6Al-4V: 100 × 4.43 = about 443 g
- Difference: about 173 g, or 64% heavier in titanium
For a machined part, use the finished volume, not the stock size. The stock size still matters for cost, because you pay for the bar or plate and the chips. Titanium chips cost far more than aluminum chips, so heavy machining from a large block increases the price quickly.
Key Takeaway: Use finished CAD volume for weight and stock volume for material cost. They answer different questions.
How Does Titanium Weight vs Aluminum Weight Change for the Same Strength?
For the same strength, the titanium weight vs aluminum weight result can reverse. Titanium can be lighter than aluminum, because its strength rises faster than its density. Compare typical yield strengths:
| Material (typical) | Yield strength (MPa) | Strength-to-weight (MPa per g/cm³) |
|---|---|---|
| 6061-T6 | about 276 | about 102 |
| 7075-T6 | about 503 | about 179 |
| Ti-6Al-4V, annealed | about 880 | about 199 |
For a tension member sized by strength, the needed cross-section falls as yield strength rises. As a result, a Ti-6Al-4V tie rod needs only about 31% of the cross-section of a 6061-T6 rod. Even at 64% higher density, it weighs about half as much.
Against 7075-T6, the advantage shrinks. A Ti-6Al-4V member sized by strength is only about 10% lighter than a 7075 member. Therefore, high-strength aluminum often closes most of the gap at a fraction of the cost.
Key Takeaway: Titanium saves real weight only against lower-strength aluminum, or when the part also needs heat or corrosion resistance.
Titanium Weight vs Aluminum Weight: Which Is Lighter When Stiffness Matters?
Aluminum is usually lighter when stiffness matters. Titanium’s elastic modulus is about 114 GPa, compared with about 69 GPa for aluminum. That is about 1.65 times higher, which almost exactly matches the density ratio. As a result, both metals have nearly the same stiffness per unit weight.
For bending, aluminum gains an extra advantage. A plate’s bending stiffness grows with the cube of its thickness, while its weight grows only linearly. Therefore, the lighter metal can use a thicker wall at the same weight and gain more stiffness. In a stiffness-limited plate, aluminum is typically around 25–30% lighter than titanium.
Typical stiffness-limited parts include:
- Base plates and machine frames
- Long brackets and arms that must not deflect
- Optical and sensor mounts
- Housings that must hold alignment
Key Takeaway: If deflection, not breaking, sets the size of the part, the titanium weight vs aluminum weight comparison favors aluminum.
When Is Titanium Worth the Extra Weight and Cost?
Titanium is worth the extra weight and cost when the part needs more than a light, stiff shape. The decision usually depends on strength, temperature, corrosion or body contact.
- High strength in a small envelope: fasteners, links and compact load-bearing parts
- Heat: titanium keeps useful strength at temperatures where aluminum alloys weaken
- Corrosion: excellent resistance in seawater and many chemicals
- Fatigue: good fatigue performance for cyclic loads
- Low thermal expansion: about 9 µm/m·K versus about 23 µm/m·K for aluminum
On the other hand, titanium conducts heat poorly. Its thermal conductivity is only a small fraction of aluminum’s. Therefore, heat sinks and thermal plates almost always stay in aluminum.
Key Takeaway: Choose titanium for strength, heat or corrosion. Choose aluminum for weight, heat transfer and cost.
How Does Machining Cost Compare for Titanium vs Aluminum?
Machining cost is usually much higher for titanium than for aluminum. Titanium is harder to cut, holds heat at the tool edge and needs lower cutting speeds. Aluminum cuts fast with high spindle speeds and long tool life.

| Factor | Aluminum (6061 / 7075) | Titanium (Ti-6Al-4V) |
|---|---|---|
| Cutting speed | High | Low |
| Tool wear | Low | High |
| Heat at the cutting edge | Carried away by chips | Stays at the tool |
| Raw material cost | Low | Several times higher |
| Typical finishes | Anodizing, hard anodizing, plating | Passivation, bead blasting, polishing |
As a result, a titanium part can cost several times more than the same part in aluminum, even before material cost. Simplifying the geometry, reducing deep pockets and using near-net stock all help. Our CNC milling and CNC turning services cover both metals.
Key Takeaway: Ask for quotes in both metals early. The cost difference often decides the material before weight does.
How Can You Reduce Part Weight Without Switching Metals?
You can often reduce part weight more by redesigning the aluminum part than by switching to titanium. Smart geometry removes material where loads are low.
- Pocketing: remove material from low-stress areas, leaving ribs.
- Ribs instead of thick walls: add stiffness with less mass.
- Higher-strength alloy: move from 6061 to 7075 where corrosion and welding allow.
- Hollow sections: use tubes or bored shafts instead of solid bars.
- Topology review: check which areas carry load before cutting.
For example, pocketing the underside of a 20 mm thick aluminum plate to a 3 mm skin with ribs can remove more than half of its weight. Multi-axis machining makes these features practical. Our guides to 4 axis CNC and 3 axis CNC machining explain how setups affect cost.
Key Takeaway: Before comparing titanium weight vs aluminum weight again, optimize the aluminum geometry first. Move to titanium only when the redesigned aluminum part still fails a requirement.
Titanium Weight vs Aluminum Weight: Which Should You Choose?
You choose between titanium weight vs aluminum weight by deciding what limits the part: shape, strength, stiffness or environment.
- Same shape, lowest weight? Aluminum.
- Stiffness-limited part? Aluminum.
- Strength-limited and small? Titanium, or 7075 aluminum to save cost.
- High temperature or seawater? Titanium.
- Heat sink or thermal plate? Aluminum.
- Tight budget? Aluminum.
In practice, when the titanium weight vs aluminum weight comparison is done properly, most machined structural parts stay in aluminum. Titanium earns its place in a smaller group of parts where strength, heat or corrosion cannot be met any other way.
Key Takeaway: Write down the one requirement the part must never fail. That requirement usually decides the metal.
What Should You Send for a Titanium or Aluminum Quote?
You should send a 3D model and a 2D drawing, plus the material options you are considering. With both, the supplier can compare titanium weight vs aluminum weight and cost on the same geometry.
- 3D model (STEP preferred)
- 2D drawing with tolerances, threads and critical features
- Material options, such as 6061-T6, 7075-T6 or Ti-6Al-4V
- Finish, such as anodizing or passivation
- Quantity for prototypes and production
We machine aluminum, stainless steel, titanium and other metals from prototype to production. Machine capability is not the same as finished-part tolerance, which is controlled per drawing. For turned and milled parts, see our guide to CNC lathe vs CNC mill.
Key Takeaway: Quote both metals on the same drawing. It shows the real price of every gram saved.
FAQ
- Q: Is titanium heavier than aluminum?
- Yes. For the same volume, Ti-6Al-4V is about 64% heavier than 6061 aluminum, at about 4.43 versus 2.70 g/cm³.
- Q: Can a titanium part be lighter than an aluminum part?
- Yes, when strength sets the size. Titanium’s higher strength lets the part be thinner, which can make it lighter than a 6061 part.
- Q: Is titanium stiffer than aluminum per weight?
- No. Both have nearly the same stiffness per unit weight, so stiffness-limited parts are usually lighter in aluminum.
- Q: How do I calculate the weight of a machined part?
- Multiply the finished volume from CAD by the material density: about 2.70 g/cm³ for 6061 and 4.43 g/cm³ for Ti-6Al-4V.
- Q: Why is titanium so expensive to machine?
- It cuts slowly, wears tools quickly and keeps heat at the cutting edge, and the raw material costs much more than aluminum.
Conclusion
Titanium weight vs aluminum weight depends on what limits the part. Aluminum is lighter for the same shape and for stiff parts; titanium is lighter only when strength sets the size. To compare both metals on your design, send your 3D model and 2D drawing to our engineers.